福克斯调出自动落锁功能的英文版-翻译

2022-08-04 14:26:23   第一文档网     [ 字体: ] [ 阅读: ] [ 文档下载 ]
说明:文章内容仅供预览,部分内容可能不全。下载后的文档,内容与下面显示的完全一致。下载之前请确认下面内容是否您想要的,是否完整无缺。下载word有问题请添加QQ:admin处理,感谢您的支持与谅解。点击这里给我发消息

#第一文档网# 导语】以下是®第一文档网的小编为您整理的《福克斯调出自动落锁功能的英文版-翻译》,欢迎阅读!
福克斯,落锁,调出,英文版,翻译

遥控钥匙调整开锁方式:同时按遥控上的开锁键和锁车键,大概3秒看到灯闪两下就OK!开锁方式可以重复设换,方法一样。

福克斯调出自动落锁功能的英文版-翻译

简单地翻译了一下,供大家参考,我准备这两天验证一下!!!!!!!

The enable/disable mode is entered when the following series of steps is performed.

Install Time: Difficulty Level:

5 Minutes 1

Directions:

Step 1

Confirm that the perimeter alarm is disarmed.

确认车辆安全停放

Step 2

Close all doors.

关闭所有车门

Step 3

Confirm that the ignition switch is in the OFF position.

Note: Steps 4 through 8 must be performed within 30 seconds.

确认车辆点火开关处于关闭状态

注意:第四步骤到第八步骤必须在30秒内完成

Step 4

Turn the ignition switch from OFF to RUN.

将点火开关从关闭到打开状态(开关从I到II状态,不要着车)

Step 5

Press the power door lock UNLOCK button three times.

将车门锁从开到关连续按动3次(关-开-关-开-关-开)

Step 6

Turn the ignition switch from RUN to OFF.

将车辆点火开关从打开到关闭状态(从II到I)

Step 7

Press the power door lock UNLOCK button three times.

将车门锁从开到关连续按动3次(关-开-关-开-关-开)

Step 8

Turn the ignition switch from OFF to RUN.

将车辆点火开关从关闭到打开状态(从I到II)

Step 9

Verify that the RAP module chirps the horn. This indicates that the RAP module is now in the enable/disable mode and ready to accept program changes.

这时行车电脑会发出短鸣声,说明行车电脑模块已经进入可编辑状态。

Step 10

Press the power door lock UNLOCK button one time to command the RAP module to toggle the autolock/relock feature ON or OFF.

将车门锁从关到开一次(关-开),以触发行车电脑模块的自动锁生效或取消。

Step 11

Press the power door lock LOCK button once to enter the command.

将车门锁从关到开一次(关-开),(RAP)执行指令。

Step 12

Verify that the vehicle horn chirps one time to signal the RAP module confirmation of the command. There should only be one chirp indicating that the autolock/relock feature has been disabled. If one chirp is heard, followed by a longer honk, the autolock/relock feature has just been enabled. Return to step 10.

这时会听到一声短鸣声,说明行车电脑模块指令已经执行。如果听到一声短鸣声,说明自动锁功能被取消,如果听到一声长鸣声,说明自动锁功能启动。重新执行第十步骤。

Step 13

Turn the ignition switch to the OFF position to exit the enable/disable mode.

将车辆点火开关转到关闭状态,退出编辑模式。

Step 14

Verify that the RAP module chirps the horn once to indicate that a feature has been changed.

会再听到一声短鸣声,表示设置成功。

本文来源:https://www.dywdw.cn/2ad66fe94afe04a1b071dea5.html

相关推荐
推荐阅读